#Profibus_DP ; ; ; Historie: ; ========= ; V1.0 01.12.2004 La Original (abgeleitet aus L100) ; V1.01 14.03.2005 La PLL entfällt, Prog64/128-Mapping neu; TZ- und Aufl-MT neu; ; V1.1 24.03.2005 La modul "S7DB (universal)" new, other modules disabled; ; ; GSD_Revision = 2 ; Vendor_Name = "Deutschmann Automation GmbH" Model_Name = "L200-PB (mit Para)" Revision = "V1.1" Ident_Number = 0x3687 Protocol_Ident = 0 Station_Type = 0 FMS_supp = 0 Hardware_Release = "-" Software_Release = "V2.1" OrderNumber = "V3487" ; 9.6_supp = 1 19.2_supp = 1 45.45_supp = 1 93.75_supp = 1 187.5_supp = 1 500_supp = 1 1.5M_supp = 1 3M_supp = 1 6M_supp = 1 12M_supp = 1 ; MaxTsdr_9.6 = 15 MaxTsdr_19.2 = 15 MaxTsdr_45.45 = 15 MaxTsdr_93.75 = 15 MaxTsdr_187.5 = 15 MaxTsdr_500 = 15 MaxTsdr_1.5M = 20 MaxTsdr_3M = 35 MaxTsdr_6M = 50 MaxTsdr_12M = 95 ; Redundancy = 0 Repeater_Ctrl_Sig = 0 24V_Pins = 0 Implementation_Type = "VPC3" Bitmap_Device = "L200" ; Freeze_Mode_supp = 1 Sync_Mode_supp = 1 Auto_Baud_supp = 1 Set_Slave_Add_supp = 1 Min_Slave_Intervall = 1 ; Modular_Station = 1 Max_Module = 17 Max_Input_Len = 39 Max_Output_Len = 31 Max_Data_Len = 70 Modul_Offset = 0 ; Fail_Safe = 0 Slave_Family = 10 ;SPS Max_Diag_Data_Len = 8 ; ; PARAMETER ; ========= ; Max_User_Prm_Data_Len = 55 ; PrmText=1 Text(0)="Keine Totzeitkompenation" Text(1)="Blockweise Totzeitkompenation" Text(2)="Bitweise Totzeitkompenation" Text(3)="Blockw. TZK (Ein-/Auszeiten)" Text(4)="Bitw. TZK (Ein-/Auszeiten)" EndPrmText PrmText=2 Text(3)="Absolute SSI" Text(1)="Absolute Parallel 24V" EndPrmText PrmText=3 Text(0)="S7-Mode" Text(1)="NSW Kommunikationsprofil" EndPrmText PrmText=4 Text(1) ="1" Text(2) ="2" Text(4) ="4" Text(8) ="8" Text(16) ="16" Text(32) ="32" Text(64) ="64" Text(128) ="128" Text(256) ="256" Text(512) ="512" Text(1024)="1024" Text(2048)="2048" Text(4096)="4096" EndPrmText PrmText=5 Text(255) ="Kein Mapping" Text(0) ="I/O-Pin 1" Text(1) ="I/O-Pin 2" Text(2) ="I/O-Pin 3" Text(3) ="I/O-Pin 4" Text(4) ="I/O-Pin 5" Text(5) ="I/O-Pin 6" Text(6) ="I/O-Pin 7" Text(7) ="I/O-Pin 8" Text(8) ="I/O-Pin 9" Text(9) ="I/O-Pin 10" Text(10) ="I/O-Pin 11" Text(11) ="I/O-Pin 12" Text(12) ="I/O-Pin 13" Text(13) ="I/O-Pin 14" Text(14) ="I/O-Pin 15" Text(15) ="I/O-Pin 16" EndPrmText PrmText=6 Text(0)="Keine Totzeitkompenation" Text(2)="Bitweise Totzeitkompenation" EndPrmText PrmText=7 Text(0)="Negativer Pegel (Aktiv = 0V)" Text(1)="Positiver Pegel (Aktiv = 24V)" Text(2)="Negative Flanke (24V -> 0V)" Text(3)="Positive Flanke (0V -> 24V)" EndPrmText PrmText=8 Text(0)="Preset1 ODER Preset 2" Text(1)="Preset1 UND Preset 2" EndPrmText PrmText=9 Text(2)="Inc. 24V (max.Count 8192)" Text(7)="Inc. 24V (max.Count 16777216)" Text(8)="Inc. RS422 (max.Count 8192)" Text(9)="Inc. RS422 (max.Count 16777216)" EndPrmText PrmText=10 Text(4096)="4096" Text(8192)="8192" EndPrmText ExtUserPrmData=1 "Totzeit-Typ" Unsigned8 2 0-4 Prm_Text_Ref=1 EndExtUserPrmData ExtUserPrmData=39 "Totzeit-Typ (MT)" Unsigned8 2 0-2 Prm_Text_Ref=6 EndExtUserPrmData ExtUserPrmData=2 "Geber-Typ-Abs." Unsigned8 3 1-11 Prm_Text_Ref=2 EndExtUserPrmData ExtUserPrmData=3 "Geberaufl./Umdr" Unsigned16 4096 2-8192 EndExtUserPrmData ExtUserPrmData=40 "Geberaufl./Umdr" Unsigned16 4096 4096-8192 Prm_Text_Ref=10 EndExtUserPrmData ExtUserPrmData=4 "Anzahl Umdrehungen" Unsigned16 4096 4096-4096 EndExtUserPrmData ExtUserPrmData=5 "Zählbereich" Unsigned32 4096 2-16777216 EndExtUserPrmData ExtUserPrmData=6 "Virtuelle Geberaufl./Umdr" Unsigned16 4096 2-32500 EndExtUserPrmData ExtUserPrmData=7 "Virt. Anzahl Umdr." Unsigned16 4096 1-4096 Prm_Text_Ref=4 EndExtUserPrmData ExtUserPrmData=8 "Virt.Zählbereich" Unsigned32 4096 2-16777216 EndExtUserPrmData ExtUserPrmData=9 "Anzahl Ausgänge" Unsigned8 16 1-16 EndExtUserPrmData ExtUserPrmData=10 "Mapping Output-Enable" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=11 "Mapping Run-Control-Output" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=12 "Mapping Dyn.Nullpunktversch." Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=13 "Mapping Program-Enable" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=14 "Mapping Program-Start" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=15 "Mapping Prog-Nr.1" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=16 "Mapping Prog-Nr.2" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=17 "Mapping Prog-Nr.4" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=18 "Mapping Prog-Nr.8" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=19 "Mapping Prog-Nr.16" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=20 "Mapping Prog-Nr.32" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=37 "Mapping Prog-Nr.64" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=38 "Mapping Prog-Nr.128" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=21 "Mapping Count-Enable" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=22 "Mapping Preset 1" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=23 "Mapping Preset 2" Unsigned8 255 0-255 Prm_Text_Ref=5 EndExtUserPrmData ExtUserPrmData=24 "Preset-Mode 1" Unsigned8 0 0-3 Prm_Text_Ref=7 EndExtUserPrmData ExtUserPrmData=25 "Preset-Mode 2" Unsigned8 0 0-3 Prm_Text_Ref=7 EndExtUserPrmData ExtUserPrmData=26 "Preset-Logik" Unsigned8 0 0-1 Prm_Text_Ref=8 EndExtUserPrmData ExtUserPrmData=27 "Inkremental-Zählfaktor" Unsigned8 1 1-100 EndExtUserPrmData ExtUserPrmData=30 "Geber-Typ-Inc." Unsigned8 8 1-11 Prm_Text_Ref=9 EndExtUserPrmData ExtUserPrmData=31 "Zeitbasis [ms]" Unsigned16 1 1-65535 EndExtUserPrmData ExtUserPrmData=33 "Presetwert" Unsigned32 0 0-16777215 EndExtUserPrmData ; ; Aufbau der allgemeinen Userspezifischen Parameterdaten: ; ------------------------------------------------------- ; ; Offset(Ref-Nr): 0 1 2 3 4(32) 5(9) ; 0x00 0x00 0x00 Rev (Log.Inputs) Anz.Ausg ; ; Offset(Ref-Nr): 6(10) 7(11) 8(13) 9(14) ; MapOutputEnab MapRunControl MapProgEnab. MapProgStart ; ; Offset(Ref-Nr): 10(15) 11(16) 12(17) 13(18) 14(19) 15(20) ; MapProgNr1 MapProgNr2 MapProgNr4 MapProgNr8 MapProgNr16 MapProgNr32 ; ; Offset(Ref-Nr): 16 17 18 19 ; MapProgNr64 MapProgNr128 0x00 0x00 ; ; ; Es folgen die Modulspez. Parameter: ; ----------------------------------- ; ; Offset(Ref-Nr): 0 1(1) 2(2) 3+4(3) 5+6(4) 7-10(5) ; Komm.Mode(0=S7,1=Komm.Prof) TZ-Typ GeberTyp GeberAufl/Umdr Anz.Umdr Zählbereich ; ; Offset(Ref-Nr): 11+12(6) 13+14(7) 15-18(8) 19(12) ; Virt.GeberAufl/Umdr Virt.Anz.Umdr Virt.Zählbereich MapDynNPV ; ; Offset(Ref-Nr): 20(21) 21(22) 22(23) 23(24) 24(25) 25(26) 26(27) ; MapCountEnab MapPreset1 MapPreset2 PresetMode1 PresetMode2 PresetLogik InkZählFaktor ; ; Offset(Ref-Nr): 27-30(33) 31(34) 32(35) 33+34(36) ; PresetWert (MapPLLInitiator MapPLLSyncFenster PLLSyncFenster_ms) ; ; Ext_User_Prm_Data_Const(0) = 0x00, 0x00, 0x00, 0x01, 0x00 ;Dieser Teil ist constant Ext_User_Prm_Data_Ref(5) = 9 ;Anz. Ausgänge = 16 Ext_User_Prm_Data_Ref(6) = 10 ;Mapping Output-Control Ext_User_Prm_Data_Ref(8) = 13 ;Mapping Prog-Enable Ext_User_Prm_Data_Ref(9) = 14 ;Mapping Prog-Start Ext_User_Prm_Data_Ref(10) = 15 ;Mapping Prog-Nr.1 Ext_User_Prm_Data_Ref(11) = 16 ;Mapping Prog-Nr.2 Ext_User_Prm_Data_Ref(12) = 17 ;Mapping Prog-Nr.4 Ext_User_Prm_Data_Ref(13) = 18 ;Mapping Prog-Nr.8 Ext_User_Prm_Data_Ref(14) = 19 ;Mapping Prog-Nr.16 Ext_User_Prm_Data_Ref(15) = 20 ;Mapping Prog-Nr.32 Ext_User_Prm_Data_Ref(16) = 37 ;Mapping Prog-Nr.64 Ext_User_Prm_Data_Ref(17) = 38 ;Mapping Prog-Nr.128 Ext_User_Prm_Data_Ref(7) = 11 ;Mapping Run-Control Ext_User_Prm_Data_Const(18)= 0x00, 0x00 ;Dieser Teil ist constant (Reserve) ; ; CONFIGURATION ; ============= ; ; Bei L200 gibt es 2 Ausführungen des Basismoduls: ; ; 1. S7-Mode ; Der Datenaustausch mit einer S7 erfolgt über einen mitgelieferten Handlingsbaustein. ; Die Programmierung (Nocken, Totzeiten...) werden NICHT im nichtflüchtigen Speicher abgelegt, ; da der Handlingsbaustein diese Daten nach jedem Einschalten an das L200 schickt. ; ;Module = "L200-Basis(S7-Mode)" 0xB7,0xA1,0x99 ; don't use for new projects ;EndModule ; ; The following modul will be used in all Deutschmann cam-switch units (R80,R100,L100,L200) ; ; Data S7->L200(Basis): Logik Logikinputs (optional) ; +----+-- ... --+----+----+----+.......+ ..... +.......+ ; |Multiplexer for DB |1-8 |9-16| 1.IO8 | | n.IO8 | ; +----+-- °°° --+----+----+----+.......+ ..... +.......+ ; 0 1 ... 6 7 8 9 ; ; Data L200(Basis)->S7: IO's IO's (optional) ; +----+-- ... --+----+----+----+----+----+----+----+----+----+----+----+.......+ ..... +.......+ ; |Multiplexer for DB | Position | Speed |Prog|Err.|1-8 |9-16| 1.IO8 | | n.IO8 | ; +----+-- °°° --+----+----+----+----+----+----+----+----+----+----+----+.......+ ..... +.......+ ; 0 1 ... 6 7 8 9 10 11 12 13 14 15 16 17 ; ; ; 2 byte logik (8..1,16..9) from S7 ------------------------------------------+ ; 2 byte for actual outputs (8..1,16..9) --------------------------------+ | ; 1 byte for actual error code -------------------------------------+ | | ; 1 byte for actual program -----------------------------------+ | | | ; 1 word for speed ---------------------------------------+ | | | | ; 2 words for position -------------------------------+ | | | | | ; 8 byte multiplexer for DB-transfer ------------+ | | | | | | ; v v v v v v v Module = "S7DB,Absolut-Single-Turn" 0xB7,0xD1,0xD0,0x90,0x90,0x91,0xA1 Ext_Module_Prm_Data_Len = 35 Ext_User_Prm_Data_Const(0) = 0,2,3,0x10,0,0,1,0,0,0x10,0,0x10,0,0,1,0,0,0x10,0,255,255,255,255,0,0,0,1,0,0,0,0,255,255,0,0 ;S7_mode, Bitw.TZK, SSI-ST, 4096x1, virt: 4096x1, Keine Mappings Ext_User_Prm_Data_Ref(2) = 2 ;Geber = SSI-ST Ext_User_Prm_Data_Ref(3) = 3 ;Aufl = 4096 Ext_User_Prm_Data_Ref(11) = 6 ;Virt.Aufl. = 4096 Ext_User_Prm_Data_Ref(19) = 12 ;Dyn.NPV-Mapping Ext_User_Prm_Data_Ref(1) = 1 ;Totzeit = bitweise 1 EndModule ; Module = "S7DB,Absolut-Multi-Turn" 0xB7,0xD1,0xD0,0x90,0x90,0x91,0xA1 Ext_Module_Prm_Data_Len = 35 Ext_User_Prm_Data_Const(0) = 0,2,6,0x10,0,0x10,0,1,0,0,0,0x10,0,0x10,0,1,0,0,0,255,255,255,255,0,0,0,1,0,0,0,0,255,255,0,0 ;S7_mode, Bitw.TZK, SSI-MT, 4096x1, virt: 4096x1, Keine Mappings Ext_User_Prm_Data_Ref(3) = 40 ;Aufl = 4096 Ext_User_Prm_Data_Ref(5) = 4 ;Anz.Umdr = 4096 Ext_User_Prm_Data_Ref(11) = 6 ;Virt.Aufl. = 4096 Ext_User_Prm_Data_Ref(13) = 7 ;Virt.Anz.Umdr = 4096 Ext_User_Prm_Data_Ref(19) = 12 ;Dyn.NPV-Mapping Ext_User_Prm_Data_Ref(1) = 39 ;Totzeit MT = bitweise 2 EndModule ; Module = "S7DB,Incremental" 0xB7,0xD1,0xD0,0x90,0x90,0x91,0xA1 Ext_Module_Prm_Data_Len = 35 Ext_User_Prm_Data_Const(0) = 0,2,3,0x10,0,0,1,0,0,0x10,0,0x10,0,0,1,0,0,0x10,0,255,255,255,255,0,0,0,1,0,0,0,0,255,255,0,0 ;S7_mode, Bitw.TZK, SSI-ST, 4096x1, virt: 4096x1, Keine Mappings Ext_User_Prm_Data_Ref(2) = 30 ;Geber = Ink-422 Ext_User_Prm_Data_Ref(3) = 3 ;Aufl = 4096 Ext_User_Prm_Data_Ref(7) = 5 ;Zählber. = 4096 Ext_User_Prm_Data_Ref(15) = 8 ;Virt.Zählber. = 4096 Ext_User_Prm_Data_Ref(20) = 21 ;Count-Enable-Mapping Ext_User_Prm_Data_Ref(21) = 22 ;Clear1-Mapping Ext_User_Prm_Data_Ref(22) = 23 ;Clear2-Mapping Ext_User_Prm_Data_Ref(23) = 24 ;ClearMode1 Ext_User_Prm_Data_Ref(24) = 25 ;ClearMode1 Ext_User_Prm_Data_Ref(25) = 26 ;ClearLogic Ext_User_Prm_Data_Ref(27) = 33 ;Presetwert Ext_User_Prm_Data_Ref(26) = 27 ;Ink-Faktor = 1 Ext_User_Prm_Data_Ref(1) = 1 ;Totzeit = bitweise 3 EndModule ; Module = "S7DB,Timer" 0xB7,0xD1,0xD0,0x90,0x90,0x91,0xA1 Ext_Module_Prm_Data_Len = 35 Ext_User_Prm_Data_Const(0) = 0,2,5,0x10,0,0,1,0,0,0x10,0,0x10,0,0,1,0,0,0x10,0,255,255,255,255,0,0,0,1,0,0,0,0,255,255,0,0 ;S7_mode, Bitw.TZK, Timer, 4096x1, virt: 4096x1, Keine Mappings Ext_User_Prm_Data_Ref(3) = 31 ;Zeitbasis = 1ms Ext_User_Prm_Data_Ref(7) = 5 ;Zählber. = 4096 Ext_User_Prm_Data_Ref(20) = 21 ;Count-Enable-Mapping Ext_User_Prm_Data_Ref(21) = 22 ;Clear1-Mapping Ext_User_Prm_Data_Ref(22) = 23 ;Clear2-Mapping Ext_User_Prm_Data_Ref(23) = 24 ;ClearMode1 Ext_User_Prm_Data_Ref(24) = 25 ;ClearMode1 Ext_User_Prm_Data_Ref(25) = 26 ;ClearLogic Ext_User_Prm_Data_Ref(27) = 33 ;Presetwert 4 EndModule ; ; ; ; 2. Kommprof-Mode ; Die Programmierung wird im nichtflüchtigen Speicher des L200 abgelegt. Die Programmierung erfolgt über das ; Deutschmann-Nockenschaltwerks-Profil oder WINLOC. ; ; Nachfolgend wird in den Modulen für beide Ausführungen nochmals unterschieden nach dem gewünschten Gebertyp. ; ; Module = " " 0 ;Dummy für Übersichtlichkeit (optische Trennung S7Mode-Profil) 6 EndModule ; Module = "Profil,Absolut-Single-Turn" 0xBC,0xA1,0x99 Ext_Module_Prm_Data_Len = 35 Ext_User_Prm_Data_Const(0) = 1,2,3,0x10,0,0,1,0,0,0x10,0,0x10,0,0,1,0,0,0x10,0,255,255,255,255,0,0,0,1,0,0,0,0,255,255,0,0 ;S7_mode, Bitw.TZK, SSI-ST, 4096x1, virt: 4096x1, Keine Mappings Ext_User_Prm_Data_Ref(2) = 2 ;Geber = SSI-ST Ext_User_Prm_Data_Ref(3) = 3 ;Aufl = 4096 Ext_User_Prm_Data_Ref(11) = 6 ;Virt.Aufl. = 4096 Ext_User_Prm_Data_Ref(19) = 12 ;Dyn.NPV-Mapping Ext_User_Prm_Data_Ref(1) = 1 ;Totzeit = bitweise 7 EndModule ; Module = "Profil,Absolut-Multi-Turn" 0xBC,0xA1,0x99 Ext_Module_Prm_Data_Len = 35 Ext_User_Prm_Data_Const(0) = 1,2,6,0x10,0,0x10,0,1,0,0,0,0x10,0,0x10,0,1,0,0,0,255,255,255,255,0,0,0,1,0,0,0,0,255,255,0,0 ;S7_mode, Bitw.TZK, SSI-MT, 4096x1, virt: 4096x1, Keine Mappings Ext_User_Prm_Data_Ref(3) = 40 ;Aufl = 4096 Ext_User_Prm_Data_Ref(5) = 4 ;Anz.Umdr = 4096 Ext_User_Prm_Data_Ref(11) = 6 ;Virt.Aufl. = 4096 Ext_User_Prm_Data_Ref(13) = 7 ;Virt.Anz.Umdr = 4096 Ext_User_Prm_Data_Ref(19) = 12 ;Dyn.NPV-Mapping Ext_User_Prm_Data_Ref(1) = 39 ;Totzeit MT = bitweise 8 EndModule ; Module = "Profil,Incremental" 0xBC,0xA1,0x99 Ext_Module_Prm_Data_Len = 35 Ext_User_Prm_Data_Const(0) = 1,2,3,0x10,0,0,1,0,0,0x10,0,0x10,0,0,1,0,0,0x10,0,255,255,255,255,0,0,0,1,0,0,0,0,255,255,0,0 ;S7_mode, Bitw.TZK, SSI-ST, 4096x1, virt: 4096x1, Keine Mappings Ext_User_Prm_Data_Ref(2) = 30 ;Geber = Ink-422 Ext_User_Prm_Data_Ref(3) = 3 ;Aufl = 4096 Ext_User_Prm_Data_Ref(7) = 5 ;Zählber. = 4096 Ext_User_Prm_Data_Ref(15) = 8 ;Virt.Zählber. = 4096 Ext_User_Prm_Data_Ref(20) = 21 ;Count-Enable-Mapping Ext_User_Prm_Data_Ref(21) = 22 ;Clear1-Mapping Ext_User_Prm_Data_Ref(22) = 23 ;Clear2-Mapping Ext_User_Prm_Data_Ref(23) = 24 ;ClearMode1 Ext_User_Prm_Data_Ref(24) = 25 ;ClearMode1 Ext_User_Prm_Data_Ref(25) = 26 ;ClearLogic Ext_User_Prm_Data_Ref(27) = 33 ;Presetwert Ext_User_Prm_Data_Ref(26) = 27 ;Ink-Faktor = 1 Ext_User_Prm_Data_Ref(1) = 1 ;Totzeit = bitweise 9 EndModule ; Module = "Profil,Timer" 0xBC,0xA1,0x99 Ext_Module_Prm_Data_Len = 35 Ext_User_Prm_Data_Const(0) = 1,2,5,0x10,0,0,1,0,0,0x10,0,0x10,0,0,1,0,0,0x10,0,255,255,255,255,0,0,0,1,0,0,0,0,255,255,0,0 ;S7_mode, Bitw.TZK, Timer, 4096x1, virt: 4096x1, Keine Mappings Ext_User_Prm_Data_Ref(3) = 31 ;Zeitbasis = 1ms Ext_User_Prm_Data_Ref(7) = 5 ;Zählber. = 4096 Ext_User_Prm_Data_Ref(20) = 21 ;Count-Enable-Mapping Ext_User_Prm_Data_Ref(21) = 22 ;Clear1-Mapping Ext_User_Prm_Data_Ref(22) = 23 ;Clear2-Mapping Ext_User_Prm_Data_Ref(23) = 24 ;ClearMode1 Ext_User_Prm_Data_Ref(24) = 25 ;ClearMode1 Ext_User_Prm_Data_Ref(25) = 26 ;ClearLogic Ext_User_Prm_Data_Ref(27) = 33 ;Presetwert 10 EndModule ; ; ; ; Es können bis zu 16 IO8-Module an die Basis angeschaltet werden. ; Für jedes IO8-Modul muss das nachfolgende GSD-Modul einmal beim Projektieren aufgerufen werden. ; Module = "L200-IO8" 0x30 12 EndModule